The Fletcher-Munson curve shows that human hearing is not equally sensitive at every frequency, and the difference shifts with volume. At low levels you hear less bass and less extreme treble, so a mix sounds thinner. At high levels they return. Mix at one steady, moderate level and check others briefly.
You finish a mix late at night, quietly, so the neighbours stay asleep. The next morning you play it loud and the low end is huge, the hi-hats are piercing, and the vocal feels buried. Nothing in the file changed. Your ears did.
That is the Fletcher-Munson curve at work, and it affects every artist who mixes their own music. This guide explains what the curve says, shows what happens to one mix at three volumes, and gives you a routine for choosing a monitoring level. If you are new to mixing, start with Music Production Basics: From Bedroom to Release first, then come back here.
What the Fletcher-Munson Curve Says
In 1933, Harvey Fletcher and Wilden Munson, researchers at Bell Labs, tested how loud pure tones of different pitches seemed to listeners at different playback levels. They found that a bass note and a midrange note played at the same physical level do not feel equally loud. The results are plotted as equal-loudness contours, and people still call them Fletcher-Munson curves. Later studies refined the measurements, and the international standard for these contours has been revised since, but the pattern holds.
The pattern is simple. Human hearing is most sensitive in the upper midrange, roughly where speech consonants and many vocal details live. It is less sensitive to low bass and to very high treble. That gap is wide when playback is quiet and narrows as playback gets louder.
So volume changes the tone you hear. At low volume, the midrange dominates and the bass and air fall away. At high volume, the bass and the top end catch up, and the whole mix feels fuller and brighter.
This is not a flaw in your speakers or your room. It is how ears work. Two practical results follow. A mix balanced at one level will sound different at another, and your listeners will play your music at every level, from one earbud on a train to a club system.
The Same Mix at Three Volumes
Take one finished mix and listen to it three ways, without touching a single fader. The table shows what most artists notice. These are descriptions of how the ear behaves, not measurements, and your room and speakers will shift the details.
What you hear | Low volume | Medium volume | High volume |
|---|---|---|---|
Kick and bass | Weak, hard to judge | Balanced, easy to place | Big, can feel boomy |
Vocal | Forward, sounds clear | Sits naturally in the mix | Can feel pushed back |
Hi-hats and cymbals | Dull, quiet | Natural | Bright, can feel harsh |
Overall impression | Thin, midrange heavy | The most trustworthy picture | Exciting, which hides problems |
Keep a short note for each song with the level you mixed at and what changed when you checked it quiet and loud. Orphiq's Notes section is a handy place for that, since you can link a note to the release it belongs to.
The trap at low volume is adding bass and treble to compensate. When you raise the level later, the track is boosted at both ends and feels bloated. The trap at high volume is the opposite. Everything sounds powerful, so you stop noticing a harsh top end or a muddy low mid, and you leave them in.
Medium volume gives the most honest balance for deciding levels and EQ. Prolonged loud listening can temporarily reduce hearing sensitivity and make tonal judgments less reliable. Keep monitoring comfortable and take breaks.
How to Choose a Monitoring Level
Pick a level you can repeat. The exact number matters less than the habit of returning to the same spot on your interface or monitor knob. A strip of tape on the knob works.
A good starting point is a volume close to a normal conversation held at arm's length. You should be able to talk over it without raising your voice. If you have a sound level meter app, note the reading once and reuse it, but treat the app as a rough guide only.
Follow these steps for every mix session:
Set your reference level before you open the session, and leave the knob alone while you balance the mix.
Build the balance at that medium level: kick, bass, vocal first, then everything else.
Make EQ decisions at your reference level, then check them briefly at other levels.
Turn it down very low for a minute. Check whether the vocal stays clear. If the kick disappears, check its midrange presence before changing the bass level.
Turn it up briefly and check for harshness in the hi-hats, sibilance and low-end boom. Do not stay there.
Return to the reference level and make the final decisions there.
For more on how to approach EQ decisions, read Audio EQ Explained for Artists.
Common Mistakes When Volume Fools Your Ears
Most volume mistakes come from a mix session that drifts. You start at a comfortable level, nudge the knob up because a part feels flat, and now every decision after that is made against a different curve.
Mixing too loud for hours. Loud monitoring is exciting and tiring. Your hearing adapts and the top end seems to disappear, so you brighten the mix to compensate. Take breaks and return at your reference level.
Judging bass only at low volume. Quiet playback hides sub-bass, so artists boost it. Check low end at medium volume and on a second system, such as a speaker in another room or a pair of headphones.
Skipping the quiet check. Many people hear music at low volume on phones and in cafes. If the vocal vanishes when you turn down, the mix will not survive that listening. This check is the reason to turn the volume down on purpose.
Treating the curve as a rule for EQ. Do not add a fixed bass or treble boost to your master to cancel the effect. Listeners play at different levels, so there is no single curve that fits everyone. A well-balanced mix at medium volume translates better than one tuned to a single level.
Gain at each stage affects what you hear too, so it helps to understand gain staging before you set your reference level. And when the mix is done, Mixing vs Mastering: What Each Step Does explains where loudness decisions belong next.
If you want a full walk-through of the mixing process itself, How to Mix a Song: Step-by-Step covers it, and Mixing Basics: A Beginner's Guide covers the fundamentals. The routine above works in any DAW and any genre, and the For Artists page shows where the rest of your music career fits around it.
Frequently Asked Questions
What is the Fletcher-Munson curve in simple terms?
It is a set of equal-loudness contours showing that ears hear bass and very high treble less well at low volume. As playback gets louder, the difference shrinks, so the same music sounds fuller and brighter.
What volume should I mix at?
Mix at a moderate, repeatable level, roughly the loudness of a conversation at arm's length. Mark your knob, return to it each session, and use brief quiet and loud checks rather than working at those levels.
Should I add bass and treble to fix the curve?
No. Listeners play music at many levels, so no fixed boost suits everyone. Balance the mix at a medium level, then confirm it still holds up when quiet and loud.
Does the curve affect headphones too?
Yes. Hearing works the same way through headphones, so level changes shift the tone you perceive. Headphones also change bass response, so check your mix on speakers and a second pair of headphones.
Read Next
From Balanced Mix to Release Day: A mix that holds up at every volume is ready for what comes next. How to Plan a Music Release: Step-by-Step Checklist walks through it, and you can ask Apollo, Orphiq's AI music strategist, to propose a release plan with tasks and due dates that you review and edit.

